Kind of Door

Many kinds of doors have specific names, depending on their purpose. The most common variety of door is the single-leaf door which consists of a single rigid panel that fills the doorway. Many variations on this basic design are possible, such as the double-leaf door or double doors and French doors that have two adjacent independent panels hinged on each side of the doorway.
A half door or Dutch door or stable door is divided in half horizontally. Traditionally the top half can be opened to allow a horse or other animal to be fed, while the bottom half remained closed to keep the animal inside. This style of door has been adapted for homes.
Saloon doors are a pair of lightweight swing doors often found in public bars, and especially associated with the American west. Saloon doors, also known as cafe doors, often use bidirectional hinges which close the door regardless of which direction it is opened by incorporating springs. Saloon doors that only extend from knee-level to chest-level are known as batwing doors.
A blind door or Gibb door is a door with no visible trim or operable components. It is designed to blend with the adjacent wall in all finishes, and visually to be a part of the wall, a disguised door.
A barn door is a door characteristic of a barn. They are often/always found on barns, and because of a barn's immense size (often) doors are subsequently big for utility.
A French door is a door (installed singly or as one of a matching pair or series) consisting of a frame around one or more transparent and/or translucent panels (called lights or lites); it is also called a French window as it resembles a door-height casement window. A pair of French doors does not generally include a central mullion (as do some casement window pairs), thus allowing a wider unobstructed opening. The frame typically requires a weather strip at floor level and where the doors meet to prevent water ingress. An espagnolette bolt allows the head and foot of each door to be secured in one movement. The slender window joinery maximizes light though into the room and minimizes the visual impact of the doorway joinery when considered externally.
A louvred door has fixed or movable wooden fins (often called slats or louvers) which permit open ventilation while preserving privacy and preventing the passage of light to the interior. Being relatively weak structures, they are most commonly used for wardrobes and drying rooms, where security is of less importance than good ventilation, although a very similar structure is commonly used to form window shutters.
A composite door is a single leaf door that can be solid or with glass, and is usually filled with high density foam. Most composite doors carry Secured by Design accreditation and PAS 23 and PAS 24.
A flush door is a completely smooth door, having plywood or MDF fixed over a light timber frame, the hollow parts of which are often filled with a cardboard core material. Skins can also be made out of hardboards, the first of which was invented by William H Mason in 1924. Called Masonite, its construction involved pressing and steaming wood chips into boards. Flush doors are most commonly employed in the interior of a dwelling, although slightly more substantial versions are occasionally used as exterior doors, especially within hotels and other buildings containing many independent dwellings.
A moulded door has the same structure as that of flush door. The only difference is that the surface material is a moulded skin made of MDF. Skins can also be made out of hardboards.
A ledge and brace door is a door made from multiple vertical planks fixed together by two horizontal planks (the ledges) and kept square by a diagonal plank (the brace).
A wicket door is a pedestrian door built into a much larger door allowing access without requiring the opening of the larger door. Examples might be found on the ceremonial door of a cathedral or in a large vehicle door in a garage or hangar.
A bifold door is a door unit that has several sections, folding in pairs. Wood is the most common material, and doors may also be metal or glass. Bifolds are most commonly made for closets, but may also be used as units between rooms.
A sliding glass door, sometimes called an Arcadia door or a Patio door, is a door made of glass that slides open and sometimes has a screen (a removable metal mesh that covers the door).
Australian doors are a pair of plywood swinging doors often found in Australian public houses. These doors are generally red or brown in color and bear a resemblance to the more formal doors found in other British Colonies' public houses.
A false door is a wall decoration that looks like a door. In ancient Egyptian architecture, this was a common element in a tomb, the false door representing a gate to the afterlife. They can also be found in the funerary architecture of the desert tribes (e.g., Libyan Ghirza).

Architectural doors have numerous general and specialized uses. Doors are generally used to separate interior spaces (rooms, closets, etc.) for privacy, convenience, security, and safety reasons. Doors are also used to secure passages into a building from the exterior for reasons of safety and climate control.

Doors also are applied in more specialized cases:

• A trapdoor is a door that is oriented horizontally in a floor or ceiling, often accessed via a ladder.
• Blast-proof doors are constructed to allow access to a structure but also to provide protection from the force of explosions.
• A garden door is any door that opens to a garden or backyard. It is often used specifically for double French doors in place of a sliding glass door (also known as Patio doors). In such a configuration, it has the advantage of a very large opening for moving large objects in and out.
• A pet door (also known as a dog door or cat flap) is an opening in a door to allow pets to enter and exit without the main door being opened. It may be simply covered by a rubber flap or it may be an actual door hinged on the top that the pet can push through. Pet doors may be mounted in a sliding glass door as a new (permanent or temporary) panel. Pet doors may be unidirectional, only allowing pets to exit. Pet doors may be electronic, only allowing pets with a special electronic tag to enter.

Door Design and styles

Many kinds of doors have specific names, depending on their purpose. The most common variety of door is the single-leaf doorwhich consists of a single rigid panel that fills the doorway. Many variations on this basic design are possible, such as thedouble-leaf door or double doors and French doors that have two adjacent independent panels hinged on each side of the doorway.

A half door or Dutch door or stable door is divided in half horizontally. Traditionally the top half can be opened to allow a horse or other animal  to be fed, while the bottom half remained closed to keep the animal inside. This style of door has been adapted for homes.

 Saloon doors are a pair of lightweight swing doors often found in public bars, and especially associated with the American west. Saloon doors, also known as cafe doors, often use bidirectional hinges which close the door regardless of which direction it is opened by incorporating springs. Saloon doors that only extend from knee-level to chest -level are known as batwing doors.

A Blind Door  or Gibb door is a door with no visible trim or operable components. It is designed to blend with the adjacent wall in all finishes, and visually to be a part of the wall, a disguised door.

A barn door is a door characteristic of a barn . They are often/always found on barns, and because of a barn's immense size (often) doors are subsequently big for utility.

A French door is a door (installed singly or as one of a matching pair or series) consisting of a frame around one or more transparent and/or translucent panels (called lights or lites); it is also called a French window as it resembles a door-height casement window. A pair of French doors does not generally include a central mullion (as do some casement window pairs), thus allowing a wider unobstructed opening. The frame typically requires a weather strip at floor level and where the doors meet to prevent water ingress. Anespagnolette bolt allows the head and foot of each door to be secured in one movement. The slender window joinery maximizes light though into the room and minimizes the visual impact of the doorway joinery when considered externally.

A louvred Door  has fixed or movable wooden fin which permit open ventilation while preserving privacy and preventing the passage of light to the interior. Being relatively weak structures, they are most commonly used forwardrobes and drying rooms, where security is of less importance than good ventilation, although a very similar structure is commonly used to form window shutters.

A composite door is a single leaf door that can be solid or with glass, and is usually filled with high density foam. Most composite doors carry Secured by Design accreditation and PAS 23 and PAS 24.

A flush door is a completely smooth door, having plywood or MDF fixed over a light timber frame, the hollow parts of which are often filled with a cardboard core material. Skins can also be made out of hardboards, the first of which was invented by William H Mason in 1924. Called Masonite , its construction involved pressing and steaming wood chips into boards. Flush doors are most commonly employed in the interior of a dwelling, although slightly more substantial versions are occasionally used as exterior doors, especially within hotels and other buildings containing many independent dwellings.

A moulded door has the same structure as that of flush door. The only difference is that the surface material is a moulded skin made of MDF. Skins can also be made out of hardbooards .

A ledge and brace door is a door made from multiple vertical planks fixed together by two horizontal planks (the ledges) and kept square by a diagonal plank (the brace).

A wicket door  is a pedestrian door built into a much larger door allowing access without requiring the opening of the larger door. Examples might be found on the ceremonial door of a cathedral or in a large vehicle door in a garage or hangar.

A bifold door is a door unit that has several sections, folding in pairs. Wood is the most common material, and doors may also be metal or glass. Bifolds are most commonly made for closets , but may also be used as units between rooms.

A Sliding Glass Door, sometimes called an Arcadia door or a Patio door, is a door made of glass that slides open and sometimes has a screen (a removable metal mesh that covers the door).

Australian doors are a pair of plywood swinging doors often found in Australian public houses. These doors are generally red or brown in color and bear a resemblance to the more formal doors found in other British Colonies' public houses.

A false door is a wall decoration that looks like a door. In ancient Egyptian architecture, this was a common element in a tomb, the false door representing a gate to the afterlife. They can also be found in the funerary architecture of the desert tribes.

history of door

The earliest records are those represented in the paintings of the Egyptian tombs, in which they are shown as single or double doors, each in a single piece of wood. In Egypt, where the climate is intensely dry, there would be no fear of their warping, but in other countries it would be necessary to frame them, which according to Vitruvius (iv. 6.) was done with stiles (sea/si) and rails the spaces enclosed being filled with panels (tympana) let into grooves made in the stiles and rails. The stiles were the vertical boards, one of which, tenoned or hinged, is known as the hanging stile, the other as the middle or meeting stile. The horizontal cross pieces are the top rail, bottom rail, and middle or intermediate rails. The most ancient doors were in timber, those made for King Solomon's temple being in olive wood (I Kings vi. 31-35), which were carved and overlaid with gold. The doors dwelt upon in Homer would appear to have been cased in silver or brass. Besides Olive wood, elm, cedar, oak and cypress were used. A 5,000-year-old door has been found by archaeologists in Switzerland. The ancient Greek and Roman doors were either single doors, double doors, sliding doors or folding doors, in the last case the leaves were hinged and folded back. In Eumachia, is a painting of a door with three leaves. In the tomb of Theron at Agrigentum there is a single four-panel door carved in stone. In the Blundell collection is a bas-relief of a temple with double doors, each leaf with five panels. Among existing examples, the bronze doors in the church of SS. Cosmas and Damiano, in Rome, are important examples of Roman metal work of the best period; they are in two leaves, each with two panels, and are framed in bronze. Those of the Pantheon are similar in design, with narrow horizontal panels in addition, at the top, bottom and middle. Two other bronze doors of the Roman period are in the Lateran Basilica.
All ancient doors were hung by pivots at the top and bottom of the hanging stile which worked in sockets in the lintel and sill, the latter being always in some hard stone such as basalt or granite. Those found at Nippur by Dr. Hilprecht, dating from 2000 B.C. were in dolerite. The tenons of the gates at Balawat were sheathed with bronze (now in the British Museum). These doors or gates were hung in two leaves, each about 8 ft 4 in (2.54 m) wide and 27 ft (8.2 m). high; they were encased with bronze bands or strips, 10 in. high, covered with repouss decoration of figures, etc. The wood doors would seem to have been about 3 in. thick, but the hanging stile was over 14 inches (360 mm) diameter. Other sheathings of various sizes in bronze have been found, which proves this to have been the universal method adopted to protect the wood pivots. In the Hauran in Syria, where timber is scarce the doors were made in stone, and one measuring 5 ft 4 in (1.63 m) by 2 ft 7 in (0.79 m) is in the British Museum; the band on the meeting stile shows that it was one of the leaves of a double door. At Kuffeir near Bostra in Syria, Burckhardt found stone doors, 9 to 10 ft (3.0 m). high, being the entrance doors of the town. In Etruria many stone doors are referred to by Dennis.
The Greek scholar Heron of Alexandria created the earliest known automatic door in the 1st century CE during the era of Roman Egypt. The first foot-sensor-activated automatic door was made in China during the reign of Emperor Yang of Sui (r. 604–618), who had one installed for his royal library. The first automatic gate operators were later created in 1206 by the Arabic inventor, Al-Jazari.
The doors of the church of the Nativity at Bethlehem (6th century) are covered with plates of bronze, cut out in patterns: those of Hagia Sophia at Constantinople, of the 8th and 9th century, are wrought in bronze, and the west doors of the cathedral of Aix-la-Chapelle (9th century), of similar manufacture, were probably brought from Constantinople, as also some of those in St. Marks, Venice.

Of the 11th and 12th centuries there are numerous examples of bronze doors, the earliest being one at Hildesheim, Germany (1015). The Hildesheim design affected the concept of Gniezno door in Poland. Of others in South Italy and Sicily, the following are the finest: in Sant Andrea, Amalfi (1060); Salerno (1099); Canosa (1111); Troia, two doors (1119 and 1124); Ravello (1179), by Barisano of Trani, who also made doors for Trani cathedral; and in Monreale and Pisa cathedrals, by Bonano of Pisa. In all these cases the hanging stile had pivots at the top and bottom. The exact period when the hinge was substituted is not quite known, but the change apparently brought about another method of strengthening and decorating doors, viz, with wrought-iron bands of infinite varieties of design. As a rule three bands from which the ornamental work springs constitute the hinges, which have rings outside the hanging stiles fitting on to vertical tenons run into the masonry or wooden frame. There is an early example of the 12th century in Lincoln; in France the metal work of the doors of Notre Dame at Paris is perhaps the most beautiful in execution, but examples are endless throughout France and England.
Returning to Italy, the most celebrated doors are those of the Battistero di San Giovanni (Florence), which together with the door frames are all in bronze, the borders of the latter being perhaps the most remarkable: the modeling of the figures, birds and foliage of the south doorway, by Andrea Pisano (1330), and of the east doorway by Ghiberti (1425–1452), are of great beauty; in the north door (1402–1424) Ghiberti adopted the same scheme of design for the paneling and figure subjects in them as Andrea Pisano, but in the east door the rectangular panels are all filled, with bas-reliefs, in which Scripture subjects are illustrated with innumerable figures, these being probably the gates of Paradise of which Michelangelo speaks.
The doors of the mosques in Cairo were of two kinds; those which, externally, were cased with sheets of bronze or iron, cut out in decorative patterns, and incised or inlaid, with bosses in relief; and those in wood, which were framed with interlaced designs of the square and diamond, this latter description of work being Coptic in its origin. The doors of the palace at Palermo, which were made by Saracenic workmen for the Normans, are fine examples and in good preservation. A somewhat similar decorative class of door to these latter is found in Verona, where the edges of the stiles and rails are beveled and notched.
In the Renaissance period the Italian doors are quite simple, their architects trusting more to the doorways for effect; but in France and Germany the contrary is the case, the doors being elaborately carved, especially in the Louis XIV and Louis XV periods, and sometimes with architectural features such as columns and entablatures with pediment and niches, the doorway being in plain masonry. While in Italy the tendency was to give scale by increasing the number of panels, in France the contrary seems to have been the rule; and one of the great doors at Fontainebleau, which is in two leaves, is entirely carried out as if consisting of one great panel only.
The earliest Renaissance doors in France are those of the cathedral of St. Sauveur at Aix (1503). In the lower panels there are figures 3 ft (0.91 m). high in Gothic niches, and in the upper panels a double range of niches with figures about 2 ft (0.61 m). high with canopies over them, all carved in cedar. The south door of Beauvais Cathedral is in some respects the finest in France; the upper panels are carved in high relief with figure subjects and canopies over them. The doors of the church at Gisors (1575) are carved with figures in niches subdivided by classic pilasters superimposed. In St. Maclou at Rouen are three magnificently carved doors; those by Jean Goujon have figures in niches on each side, and others in a group of great beauty in the center. The other doors, probably about forty to fifty years later, are enriched with bas-reliefs, landscapes, figures and elaborate interlaced borders.
When it comes to the world's largest door, there is not just one, in fact there are four and they all belong to NASA's Vehicle Assembly Building at the Kennedy Space Center. The Vehicle Assembly Building was originally built to assembly of Apollo and Saturn vehicles and is now used to support Space Shuttle operations. Each of the four doors are 139 meters or 456 feet high, in comparison the Statue of Liberty is only 93 meters or 305 feet high.
The oldest door in England can be found in Westminster Abbey and dates from 1050. In England in the 17th century the door panels were raised with bolection or projecting moldings, sometimes richly carved, round them; in the 18th century the moldings worked on the stiles and rails were carved with the egg and tongue ornament.

People wanted style in their garage doors

As architecture changed, so did people’s ideas of garages.
Because of the decreasing amount of available space, garages had to be moved closer to the houses.
So architects decided to incorporate them right into the design of the house themselves, giving them the same style and color as the rest of the house.
So as the variety of house designs expanded, so did garage designs.
All kinds of house and garage styles were sought out, like Colonial, French, Mediterranean, and even Old English.
One of the more popular architectural forms was Craftsman, with their open framework, their lattices, and their pergolas. The garage was indeed becoming an architectural marvel – and, of course, the garage doors had to match. So the demand for fancier garage doors became widespread, and the industry flourished.

200 Different illustrations of Designs of the finest Carved Doors

In these troubled times doors were built for security to delay indeed stop anyone forcing entry into the house, and also in the most important houses were built to impress , the finest houses had carved doors and were detailed and richly carved in the by master craftsmen for the finest houses (constructed principally of  Oak because of its strength and durability ) But the principle function of the doo with its strong heavy construction was because it was designed to delay or stop forced entry to the house
 The size and position of doorways in Tudor buildings were dictated by the practical requirements of access and construction.
Tudor carved and plain door heads were of  wood, stone or brick, and tended to be flat or four-centred  (that is, in the form of a shallow arch that rises to a central point). Four centred heads sometimes had carved spandrels(examples are shown in web photos). The jambs often had stopped, chamfered mouldings, to protect and decorate the frame.
Carved and Plain Door Hoodmolds or projecting carved or moulded cornices were cut over front doors and, during the 16th century, porches became popular.
Internal Porch Pain or carved doorways, protected from the weather, were often more elaborate than external doorways.  Their decorative development became more detailed in carved design as the century progressed and is similar to that of the fireplace over mantle. Classical details such as pillars and cornices appeared from the middle of the 16th century , but for security of the occupants late medieval style and design were of a strong heavy plain or carved door construction this design criteria remained dominant throughout the Tudor  period.
External plain or carved doors were made from oak planks with carved detailed mouldings the oak was up to 26 inches (65cm) wide. The planks were either fastened by horizontal battens on the reverse or for strength and security by a second set of planks, laid at right angles to the first (a double-boarded or cross-boarded door).
The heads of the handmade nails used on the plain or carved door construction were sometimes left exposed to give a decorative finish . Ordinary internal plain or carved doors were usually battened. Grander plain or carved doors were often lighter, comprising a framework with an infill of frequently carved wooden door panels. Door fittings were basic, except in the grandest houses.

choosing a form of door

The door of his role has been known for a long time. If the first door serves as an intermediary between the exterior of the building to the inside, or pengubung between a room with another room, as well as to maintain the privacy of the household, now the door can add aesthetic value. Because now with the development of technology, more and allow the emergence of various types, designs, sizes, and materials of the door.
There are so many types and forms of the door, flair and creativity required in selecting appropriate placement and function rooms will be given door. Here are some Tips for Choosing a house door and door models from us as "providers of services of an architect" you should look for, including durability of the door itself. Make sure you select the proper type and material. Do not choose a too thin and easily discolored by the weather, especially for the main doors and exterior doors.
Next is the appearance. Make sure the style and motif as well as color matching door home design concept itself. Suppose you choose a classic design of the house and gave the door a modern minimalist, this course will not fit. When the concept of ethnic style house, carved doors could use as the main door of your house.
Another criterion is soundproof. In addition to the security guard, outside the door as much as possible could be dampening the noise from the street. Indeed, in terms of acoustics, the walls have more tasks, but the door must help support if you want to muffle the noise from outside or from the room terntentu. Similarly with the bedroom door. Should be selected soundproofing material to maintain the privacy of the occupants of the room.
The next criterion is to support inter-room air circulation. Placement should be adjusted towards the door with a circulation of air so that air can flow from outside to inside the home, and vice versa.
If you want natural light into a room (especially on the exterior door), door glass element damage is a good option. You can add a curtain to adorn the doors are also functions to absorb heat from the sun outside.

 

DOOR DECORATION

Mungkin maksud Anda adalah: hiasan pintu

Ketikkan teks atau alamat situs web atau terjemahkan dokumen.

Batal

Oasis not only to stick the flowers. Given the twinkling of paper winding and tape, oasis could be pretty door decoration!Friendly welcome guests to give satisfaction for residents and visitors. Believe it or not, friendliness will have an impact on the beauty of the house. Friendly impression could arise from percantikan front of your home.One dicantelkan creations at the main entrance to provide "color" before entering into the house. Especially if there are any events that you celebrate, such as Christmas.Synonymous with Christmas joy and cheer. Excitement can you show from the front of the house. Here we display the main door decorations for your home look attractive. 

How to make house door

It is important from the manufacture of a door frame is a match between the size of the frames and doors that will be paired with the frame, both width and height, and (especially) the thickness of the door.Door leaf thickness was instrumental to making skonengan groove on the frame so later after hanging on the frame and fastened to the skonengan, door sills are not mumbul of penggantungnya.Invented door (ready to put) the industrial production sold in many specialty shops with attractive models and high quality. Therefore, people often choose to buy a door so rather than ordering on artisan frame maker. Unfortunately, industry / factories do not usually co-produced frame so the frame must be ordered separately in frame builders.The most ideal thing is to book a package. Doors and frames are made by the same maker. The goal is that the material for the manufacture of timber frames and doors are from a single source so that the texture and color of doors and frames are not much different. Also to maintain the uniformity of quality of manufacture.Compared with the making by a qualified, factory production or high-tech industry with cutting-edge machines clearly better guarantee of quality.As an illustration, industrial / plant generally has a drying room or oven (dry-kiln) to "vaporize" the water content in the wood, so gone are the most preferred moisture hordes of termites. Coupled with a dedicated space to "inject" certain chemicals into the wood pores to add strength and durability of wood.Quite a relief too, that now has been sold at retail various types of wood that has been through the process ovenisasi.Luxury home is strongly influenced by the appearance of the door. Sometimes, when listened to with jelly, then in fact precisely the building looks much as it is influenced by the design luxury door.and the thickness of the door. Thickness of the door leaf to make a very important role sponengan groove on the frame, so that after hanging on the frame and fastened to the sponengan, door sills are not mumbul of penggantungnya.Currently invented door (ready to install) the results of industrial production sold in many specialty shops with models attractive design and quality. Therefore, people often choose to buy ready-made doors rather than ordering on artisan frame maker.Unfortunately, the industry or plant is usually not co-produced frame so the frame must be ordered separately in the builder. The most ideal thing is to book a package.Typically, doors and frames are made by the same maker. The goal is that the material for the manufacture of timber frames and doors are from a single source so that the texture and color of doors and frames are not much different. Also, to maintain uniformity in the quality of manufacture.Compared with the making by a qualified, factory production or high-tech industry with cutting-edge machines clearly better guarantee of quality. As an illustration, industrial or factory generally have a room or oven drying (dry klin) to "evaporate" moisture content in wood, so gone are the most preferred moisture hordes of termites. That would be coupled with a special room to "inject" certain chemicals into the wood pores to add strength and durability of wood. Quite a relief too, that now has been sold at retail various types of wood that has been through the process ovenisasi.The size of the door of a house should look proportionate to the method of comparison between the height and width of the door to the high ceiling or high ceiling. Minimalist design of the door took a lot of interest, especially if the material the door and frame are made of teak wood.Actually, a variety of door designs can be found easily. Only, the concept of home design, either classical or modern minimalist, should be a consideration factor to obtain the exact composition. Therefore, try to always get the right size composition in the design of the house and the door.Doors with a ruler measuring geomancy (feng shui)In the science of feng shui, the door is the flow of chi to enter and exit through the door jamb hole. The main door should be larger than all of the access door in the house. That is, the natural energy or chi flows through the main door will result in great good luck for the occupants of the house.However, the fortunes of each house was calculated based on the birth of the household. Similarly, the size of doors, height and width based on the occupants of the house, especially heads of households.Geomancy ruler on the market today based solely on the global exposure because it is not designed for the birth of a person based on an accurate date of birth. Therefore, the method of calculating the appropriate feng shui is the height and width of the door should be calculated on the basis of the household.According to fengshui, the door should be a matter of luck rather than by frame width or height sponeng the outside, but based on height width inner door jamb. Calculations with a ruler or a ruler to feng shui for housing include Treasury, Pain, Go, Bakti, Position, Loss, natural disasters and Capital.Each size of the bar gives its own meaning in the life of a career and marriage. Many homes are sold by well-known developers using feng shui appropriate bar size. In fact, many wealthy businessmen to buy plots of land and build their own home or place of business.Taking the bar fengshui done to get the most out of home design and composition of the accuracy of the application of feng shui to enhance the glory of the household. However, based on surveys in the field, especially for low-cost housing construction, design and feng shui concepts are rarely applied. This happens because the simple concept sometimes overlooked for some reason. So, what happens is, the rich get richer, the poor continue to be poor.The application of the concept of feng shui in the home can be felt when the house was occupied 6 years to 12 years. Influential impact on the house such as loss or corrosion on the iron, will be felt gradually. It has been proved by our ancestors in the past up to now finally be accepted by fengshui western people.

DOOR’S MATERIAL FOR HOUSE

 >Doors and windows is one important element in building a house. The need for an artistic considerations toshape it. Door frames and shapes can reflect the personality of the homeowner. Pick the door and window framesare appropriate for visitors to the house, although we feel comfortable standing in front of the new house.

Selecting doors and windows are not as easy as selecting other furniture. Generally, the selection of doors andwindow frames are considered the umpteenth number of home design. But if the frames and doors do not fit with the design of our home, not only reduces the beauty, but it can also ruin the beauty of our homes.

The door is part of the first seen by our guests, because of its position in front of the house. That's why the dooris also often considered the most interesting guests eyes. And the development of door frames and window sillshave a lot of progress, both in terms of components, as well as panel and vent.
Door and window frames
Selecting doors and window frames of wood to fit against the house and the building would be adapted to the style of the room as well as the soul of the house itself.
Doors and window frames with a classic style combined with the vent is certainly less pleasing to the eye. Or asdoors and window frames that are loved minimalist must comply with the concept of home when his house wasnot forced to use the classic concept.

Alpha>Dropped on a wooden frame option is not without reason, wood is very easy to set up and have a more aesthetic value than frames made of aluminum, the following are some disadvantages of using aluminum frames for buildings:

1. Variations are limited, because it is a factory standard, limited to the shape of classical minimalism and Europe.
2. Installation by using the Fischer system. This technique relies on the strength of diborkan fischer screws and planted along the frame against the wall around the door frame that has been plastered neatly and very accurate
size and angle of the elbow. For this installation technique, if something goes wrong in the installation, it can be fatal.
3. The assembly of aluminum frames paired the strength of the screws that attach to the walls must be fitted with precision made and plastered neatly to avoid leaks and other errors.
Do not choose a low-quality aluminum frame, because it can easily expands as the temperature changes drastically as a framed glass can be easily separated.
4. Poor connection at the elbow or the glass can cause rain water to enter, because the splicing factors and "sealant" or the rubber seal between the glass and aluminum must be of high quality and durable materials so that water does not easily fit into the frame or into the room. Basically the problem is not a problem sealant on aluminum frames because aluminum is not affected water